Steel Products Prices North America
![](https://www.steelmarketupdate.com/wp-content/uploads/sites/2/media/k2/items/src/ccbba87e5d056d791ff9f2622d754fe4.jpg)
SIMA: Steel Import License Data for December Lowest Since 2009
Written by Peter Wright
January 13, 2020
December’s licensed import volume for rolled steel products was the lowest since December 2009. Year over year, total rolled product imports in December were down by 27.8 percent on a three-month moving average (3MMA) basis. This follows the 27.4 percent decrease in November, 17.7 percent decrease in October and 15.5 percent decline in September on the same basis.
This early look at December’s import volume is based on Commerce Department license data (see explanation below.) This import analysis includes all major steel sectors: sheet, plate, longs and tubulars, with a total of 18 subsectors. We now publish an import market share analysis for the same 18 steel product groups. All volumes in this analysis are reported in short tons. We use three-month moving averages rather than single-month results to smooth out monthly variability.
Imports of total rolled products in December were the lowest since December 2009 on a single-month basis and the lowest since February 2010 on a 3MMA basis. In the 12 months August 2018 through August 2019, total rolled product imports on a 3MMA basis were consistently in the range of 1.70 to 1.94 million tons. The September, October, November and December total rolled product volumes broke out of that range to the downside at 1.65, 1.54, 1.38 and 1.30 million tons, respectively. Year over year on a 3MMA basis, sheet products were down by 25.8 percent, plate products were down by 37.6 percent, long products were down by 22.4 percent and tubulars were down by 30.7 percent. Imports of flat rolled, tubulars and longs all had a recent peak in May 2018. Since then total flat rolled (sheet + plate) imports have consistently declined, which may be tariff driven. This is not so obvious for longs and tubulars where the decline since May 2018 has been less consistent.
Figure 1 shows the tonnage of total rolled steel and semifinished imports through December on a 3MMA basis. Total rolled product volume has been on an erratically downward trend since mid-2017. Imports of semifinished have been very erratic since July 2018, ranging from a high of 1.28 million tons in April 2019 to a low of 0.21 million tons in August 2019. December’s volume was 917,998 tons, therefore in the top half of the range. This is why we use a 3MMA calculation in our analyses, the result of which is the much smoother line for semis in Figure 1. The Section 232 legislation has had no effect on semifinished product imports.
Figure 2 summarizes the import volume of flat rolled, tubular and long products since 2004 on a 3MMA basis. All three have been trending down since mid-2017.
There are three tables in this report. In each of them we show the 3MMA of the tonnage in December 2019 and December 2018 with the year-over-year change. We then calculate the percentage change in volume in the most recent three months with the previous three months. This month we are comparing October through December with July through September (3M/3M). The next column to the right shows the year-over-year change as a percentage. Declines are color coded green and increases are coded red. Finally, in the far-right column, we subtract the 12-month change from the three-month change. This is a way of describing the magnitude of the recent momentum as a percentage. It is not unusual for the color code of the momentum to be the opposite of the two-time frame analyses, which it was in December.
Table 1 describes the imports of all major sectors of the sheet and plate markets. In the flat rolled sectors shown in Table 1, total sheet products were down by 25.8 percent and total plate products were down by 37.6 percent, both year over year. All individual products in the sheet and plate groups were down year over year. Figures 3 and 4 show the history of sheet and plate product imports since January 2004.
Table 2 shows the same analysis for long products where the year-over year volume was down by 22.4 percent in total. Wire rod was down the most as rebar, light shapes and heavy structurals increased. Figure 5 shows the history of long product imports.
Table 3 shows that for tubular products in total the volume was down by 30.7 percent year-over-year with line pipe down the most and structural tubing being the only product to experience an increase. Line pipe declined by 56.1 percent. Figure 6 shows the history of tubular imports since January 2004.
Explanation: SMU publishes several import reports ranging from this very early look using license data to the very detailed analysis of final volumes by product, by district of entry and by source nation, which is available in the Premium member section of our website. The early look is based on three-month moving averages using the latest license data, either the preliminary or final data for the previous month and final data for earlier months. We recognize that the license data is subject to revisions but believe that by combining it with earlier months in this way gives a reasonably accurate assessment of volume trends by product as early as possible. The main issue with the license data is that the month the tonnage arrives is not always the same month in which the license was recorded. In 2014, we conducted a 12-month analysis to evaluate the accuracy of the license data compared to final receipts. This analysis showed that the licensed tonnage of all carbon and low alloy products was 2.3 percent less than actual receipts, close enough to confidently include license data in this current update. The discrepancy declined continuously during the 12-month evaluation as a longer period was considered.
Statement from the Department of Commerce: The Steel Import Monitoring and Analysis (SIMA) system of the Department of Commerce collects and publishes data of steel mill product imports. By design, this information gives stakeholders valuable information on steel trade with the United States. This is achieved through two tools: the steel licensing program and the steel import monitor. All steel mill imports into the United States require a license issued by the SIMA office. The SIMA Licensing System is an online system for importers to register, apply for and receive licenses in a timely manner. In addition to managing the licensing system, SIMA publishes near-real-time aggregate data on steel mill imports into the United States. These data incorporate information collected from steel license applications and publicly released Census data. The data are displayed in tables and graphs for users to analyze. Additionally, SIMA provides data on U.S. steel mill exports, as well as imports and exports of select downstream steel products.
![](https://www.steelmarketupdate.com/wp-content/uploads/sites/2/2023/04/peter-wright.png)
Peter Wright
Read more from Peter WrightLatest in Steel Products Prices North America
![](https://www.steelmarketupdate.com/wp-content/uploads/sites/2/images/Featured_News_Icons/Nucor.png)
Nucor inches HR price up, aims for $695/ton
Nucor increased its consumer spot price (CSP) for hot-rolled (HR) coil to $695 per short ton (st), up $5/st from last week.
![](https://www.steelmarketupdate.com/wp-content/uploads/sites/2/images/Featured_News_Icons/Nucor.png)
Nucor maintains $690/ton HR base price
Nucor’s weekly consumer spot price (CSP) for hot-rolled (HR) coil is unchanged from last week at $690/ton.
![](https://www.steelmarketupdate.com/wp-content/uploads/sites/2/2023/07/CRU-Logo-2023-07-21-at-4.35.41-PM.png)
CRU: US prices find a bottom as other markets fall
The US sheet market appears to have reached a bottom following consistent weekly declines since April. However, other markets remain weak due to limited demand. Trading in Europe has been slow due to summer holidays. While European mills are also undergoing maintenance outages, these have not been enough to offset ongoing price falls, with weak […]
![](https://www.steelmarketupdate.com/wp-content/uploads/sites/2/images/Featured_News_Icons/Cliffs_logo2.2.png)
Cliffs seeks $700/ton for HR, up $30/ton from last week
Cleveland-Cliffs said on Wednesday that it would seek at least $700 per short ton (st) for hot-rolled (HR) coil. The Cleveland-based steelmaker said it made the move "due to ongoing market developments." The company said the increase was effective immediately for HR orders for September.
![](https://www.steelmarketupdate.com/wp-content/uploads/sites/2/images/Featured_News_Icons/Nucor.png)
Nucor aims for $675/ton for HR
Nucor has raised its consumer spot price (CSP) for hot-rolled (HR) coil to $675 per short ton (st), up $25/st from last week.