Steel Products Prices North America
Raw Materials Prices: Iron Ore, Coking Coal, Pig Iron, Scrap, Zinc
Written by Peter Wright
October 23, 2019
Compared to three months ago, all five of the raw materials prices considered in this report declined in October. Compared to September, there was a recovery in the prices of coking coal and zinc.
Table 1 summarizes the price changes through Oct. 16 of the five materials considered in this analysis. It reports the month/month, three months/three months and 12 months/12 months changes on a percentage basis. Iron ore and coking coal had price reversals since our September update as the price of iron ore declined and that of coking coal advanced.
Iron Ore
Based on CRU’s data, the weekly average spot price of 62% fines delivered North China was $92.00 per dry metric ton on Oct. 16, down from $94.00 Sept. 25 and down from $120.50 on July 17. Figure 1 shows the price of 62% Fe delivered North China since January 2009. The price of ore is still above the $20 range that prior to February 2019 had existed for a year and a half.
Coking Coal
The price of premium low volatile coking coal FOB east coast of Australia declined each month June through September, then recovered from $133 in September to $146 per metric ton in October (Figure 2).
Pig Iron
Most of the pig iron imported to the U.S. currently comes from Russia, Ukraine and Brazil with additional material from South Africa and Latvia. In this report, we summarize prices out of Brazil and average the FOB value from the north and south ports. The price had a recent peak of $400 per metric ton in May and June last year and has declined steadily ever since, reaching $302.50 on Oct. 16. The average price in October was 12.9 percent lower than in October last year (Figure 3).
Scrap
To put this raw materials commentary into perspective, we include here Figure 4, which shows the spread between busheling in the Great Lakes region and hot rolled coil Mid West U.S. through mid-October 2019, both in dollars per net ton. The spread collapsed from $564 in October last year to $285 in June before recovering to $310.57 in October 2019. It is now at the top end of the range that has been relatively normal for the last 13 years.
Figure 5 shows the relationship between shredded and busheling both priced in dollars per gross ton in the Great Lakes region. This spread was $5 in October, the lowest since May 2016.
Figure 6 is a scatter gram of the price of Chicago shredded and the monthly Broad Index value of the U.S. dollar as reported by the Federal Reserve. The latest data for the monthly Broad Index was September. This is a causal relationship with a negative correlation of almost 73 percent.
There is a long-term relationship between the prices of iron ore and scrap. Figure 7 shows the prices of 62% iron ore fines delivered North China and the price of shredded scrap in the Great Lakes region through late October 2019. The correlation since January 2006 has been over 79 percent. There was a very unusual divergence in these prices in 2017 and 2018 that benefited the integrated producers, but that situation has now corrected leaving the EAF producers with an advantage on a historical basis.
In the last 11 years, scrap in dollars per gross ton has been on average 3.4 times as expensive as iron ore in dollars per dry metric ton (dmt). A high ratio benefits the domestic integrated producers and a low ratio benefits the EAF producers. The ratio has been erratic since mid-2014, but at 2.3 in October gives a substantial advantage to the EAF producers (Figure 8).
Zinc
The LME cash price for zinc mid-month is shown in Figure 9. The latest data is for Oct.16. when the price was $1.11 per pound, down every month from March through August with a small rebound in September that accelerated in October.
Zinc is the fourth most widely used metal in the world after iron, aluminum and copper. Its primary uses are 60 percent for galvanizing steel, 15 percent for zinc-based die castings and about 14 percent in the production of brass and bronze alloys.
Peter Wright
Read more from Peter WrightLatest in Steel Products Prices North America
SMU Community Chat: Timna Tanners on ‘Trumplications’ for steel in 2025
Wolfe Research's Managing Director Timna Tanners discusses the 'Trumplications' for steel in the coming year in this week's SMU Community Chat.
Nucor raises hot rolled spot price to $750/ton
Nucor raised its weekly consumer spot price (CSP) for HRC this week to $750/short ton.
SMU price ranges: Most sheet and plate products drift lower
Steel sheet prices mostly edged lower for a second week, while plate prices slipped for the third consecutive week.
Nucor drops HRC price to $720/ton
After holding its weekly spot price for hot-rolled (HR) coil steady for three weeks at $730 per short ton (st), Nucor lowered the price this week by $10/st.
SMU price ranges: Sheet slips, plate falls to 45-month low
Steel sheet and plate prices moved lower this week as efforts among some mills to hold the line on tags ran up against continued concerns about demand.