The U.S. steel industry produced approximately 24 million tons of steel in the first quarter of 2019, a 6.7 percent increase from the same period last year. Mill utilization averaged 81.8 percent, up more than 5 percentage points from the 76.6 percent in 2018. U.S. raw steel production for the week ending March 30 dipped […]
Production at U.S. steel mills eased slightly in the week ending March 16, maintaining an average capability utilization rate of 82.9 percent, down from the 10-year high of 83.4 percent reported in the prior week. Domestic raw steel production for the week totaled 1,930,000 net tons, down 0.6 percent from the prior week but up […]
U.S. steel mills continued to raise the productivity bar, reaching an average capability utilization rate of 83.4 percent in the week ending March 9. Domestic raw steel production for the week totaled 1,941,000 net tons, up 0.7 percent from the prior week and 6.3 percent from the same period last year, reported the American Iron […]
Total raw steel production for the month of January rose to 8,286,886 net tons, reports the American Iron and Steel Institute in Washington. This is one of the higher levels seen over the last few years. Broken down by production method, 5,717,191 tons (69.0 percent) were produced by electric arc furnaces (EAFs) and 2,569,695 tons […]
U.S. steel mills reached an average capability utilization rate of 82.8 percent in the week ending March 2. Domestic raw steel production for the week totaled 1,927,000 net tons, up 1.0 percent from the prior week and 5.9 percent from the same period last year. This is the highest capacity utilization rate seen in over […]
For the week ending Feb. 23, domestic raw steel production totaled 1,907,000 net tons. The mills achieved an average capability utilization rate of 81.9 percent, up 1.1 percent from the prior week and 5.0 percent from the same period last year. The U.S. steel industry has produced 14,644,000 tons of steel so far in 2019, […]
The U.S. steel industry has produced 12,737,000 tons of steel so far in 2019, an 8.4 percent increase from the same period last year. Mill utilization has averaged 80.7 percent this year, up substantially from the 75.7 percent in 2018, reported the American Iron and Steel Institute. For the week ending Feb. 16, the average […]
The average capability utilization for U.S. steelmakers hit 81.5 percent in the week ending Feb. 9, the highest rate in about three months, with the mills producing 1,897,000 net tons of steel. Production increased 0.4 percent from the prior week and was up 4.4 percent from the same week the prior year, reported the American […]
Harsh winter weather likely contributed to a slight slowdown in the rate of raw steel production last week after two weeks above 1.9 million tons. U.S. steelmakers produced 1,889,000 net tons of steel in the week ending Feb. 2, operating at a capability utilization rate of 81.2 percent. Production was down 1.7 percent from the […]
U.S. steelmakers operated at 81.1 percent of their capability in the week ending Jan. 26, producing 1,922,000 net tons of raw steel. It has been a year since the mills produced that much in a single week. It was also the second week this month that steel production was above 1.9 million tons. Steel production […]
Raw steel production by U.S. steelmakers in the week ending Jan. 19 totaled 1,912,000 net tons for a capability utilization of 80.7 percent. Steel production was up 1.1 percent from the prior week and up 11.5 percent from the same week last year when the utilization rate was 73.6 percent, reported the American Iron and […]
Raw steel production by U.S. steelmakers in the week ending Jan. 12 totaled 1,891,000 net tons for a capability utilization of 79.8 percent. Steel production was up 0.8 percent from the prior week and up 10.3 percent from the same week last year when the utilization rate was 73.6 percent, reported the American Iron and […]
I was asked this evening if the JSW Ohio production tonnage is included in the weekly raw steel production report produced by the American Iron & Steel Institute (AISI). In the fine print of their weekly report, the AISI states that 1st Quarter 2019 production is estimated at 30.5 million tons, which is lower than […]
U.S. mills began the new year with little sign of a slowdown. Raw steel production by U.S. steelmakers in the week ending Jan. 5 totaled 1,876,000 net tons for a capability utilization of 80.0 percent. Steel production was down a slight 1.2 percent from the prior week, but up 10.1 percent from the same week […]
Cranking out steel at more than 80 percent of capacity late in the year, U.S. mills produced over 95 million tons of raw steel in 2018, 6.2 percent more than the prior year, according to weekly production data from the American Iron and Steel Institute. The average capacity utilization rate for the year increased by […]
Total raw steel production for the month of November was 8,156,077 net tons. Broken down by production method, 5,533,449 tons (67.8 percent) were produced by electric arc furnaces (EAFs) and 2,622,628 tons (32.2 percent) were produced by blast furnaces. November production was 174,428 tons or 2.1 percent lower than October, but 836,610 tons or 11.4 […]
Raw steel production by U.S. steelmakers in the week ending Dec. 15 inched up to 80.6 percent capability utilization. Steel production totaled 1,890,000 net tons for the week, up 0.7 percent from the prior week, and up 12.8 percent from the prior year, reports the American Iron and Steel Institute. Domestic mills have been running […]
Demand for long products is booming, plate products are doing OK, sheet products are flat and tubulars are cratering. This analysis by SMU staff is based on data from the American Iron and Steel Institute (AISI) and the U.S. Department of Commerce (DoC). The analysis summarizes total steel supply by product from 2003 through October […]
Total raw steel production for the month of October was 8,330,505 net tons, the highest production level since August 2014 when 8,546,303 tons were produced. Broken down by production method, 5,724,209 tons were produced by electric arc furnaces (EAFs) and 2,606,296 tons were produced by blast furnaces. October production was 333,505 tons or 4.2 percent […]
Raw steel production by U.S. steelmakers in the week ending Dec. 8 saw a slight dip for the third week in a row, possibly reflecting seasonal weaknesss, but stayed at the 80.0 percent capacity utilization level the mills strive to maintain. Steel production totaled 1,876,000 net tons for the week, down 0.8 percent from the […]
Raw steel production by U.S. steelmakers in the week ending Dec. 1 backslid a bit, but stayed above the 80 percent level that the mills hope to maintain. Steel production totaled 1,892,000 net tons for the week, down a slight 0.7 percent from the prior week, but up 11.1 percent from the prior year. The […]
This is the first time we have done this analysis since our April publication and we were surprised that the results for sheet and strip products weren’t as good as we expected. Our analysis is based on data from the American Iron and Steel Institute (AISI) and the U.S. Department of Commerce (DoC). The analysis […]
U.S. steelmakers have produced 5.6 percent more raw steel so far this year. Adjusted year-to-date production through Nov. 24 totaled 85,639,000 net tons. The increase is the result of a nearly 4 percent improvement in capacity utilization, to an average annual rate of 78.1 percent from 74.2 percent in 2017, reports the American Iron and […]
Mill utilization among domestic steelmakers continues to inch upward and is now well above the profitable 80 percent level the industry hopes to maintain. U.S. raw steel production for the week ending Nov. 17 totaled 1,924,000 net tons for a capability utilization rate of 82.1 percent, a half-percent more than the prior week and a […]
Domestic steelmakers have been able to sustain operations above 80 percent capacity utilization for a month now, keeping production at the highest rate seen in a decade. U.S. raw steel production for the week ending Nov. 10 totaled 1,915,000 net tons, a utilization rate of 81.7 percent, just slightly below the prior week, but a 12.1 […]
Domestic steelmakers achieved their highest production rate in a decade last week, hitting a capability utilization of 81.8 percent. The last time production was higher was the week ending Sept. 27, 2008, when the mills operated at 83.2 percent and produced nearly 2 million tons. U.S. raw steel production for the week ending Nov. 3 […]
Domestic steel mills achieved a production rate last week not seen in more than six years. U.S. raw steel production for the week ending Oct. 27 totaled 1,898,000 net tons with the mills averaging 81.0 percent of their capability, up from 80.0 percent reported the prior week, according to the American Iron and Steel Institute. […]
U.S. mills have operated at 80 percent of capacity or better for two weeks in a row. U.S. raw steel production for the week ending Oct. 20 totaled 1,875,000 net tons with the mills averaging 80.0 percent of their capability, down slightly from 80.2 percent reported the prior week, according to the American Iron and […]
Gaurav Chhibbar is a partner at Metal Edge Partners, a firm engaged in Risk Management and Strategic Advisory. In this new role, he and his firm design and execute risk management strategy for clients along with providing process and analytical support. In Gaurav’s previous role, he was a Trader at Cargill spending time in Metal […]
U.S. raw steel production for the week ending Oct. 13 totaled 1,881,000 net tons with the mills operating at 80.2 percent of capacity, reported the American Iron and Steel Institute. The current week’s production is a 1.6 percent improvement from the prior week, and a 10.3 percent jump from the same period last year, when […]