Buyers polled by Steel Market Update this week reported little change in the tight market conditions. Mills have few spot tons to offer, and those that are made available get snapped up immediately. Most of the limited spot buys on hot roll are transacting at around $1,300 per ton, but offers reportedly have ranged up […]
Among steelmaking raw materials, the prices of pig iron, shredded scrap, busheling scrap and aluminum rose again in March on top of large gains in previous months. Prices increased as much as 14% month-over-month for those four products. Iron ore prices are slightly down compared to levels one month prior, while coking coal prices have […]
Lead times for spot orders of most steel products appear to have leveled off a bit in the past two weeks, based on Steel Market Update’s latest check of the market. All flat rolled and plate products registered small declines except for Galvalume, which was the only one to see an increase in delivery times […]
Hot rolled steel prices reached another eyebrow-raising milestone this week, hitting an average of $1,300 per ton ($65/cwt), which is an all-time record even adjusting for inflation from the previous high of $1,070 per ton recorded by Steel Market Update in 2008. Flat rolled prices rose by an additional $10-30 per ton as the market […]
Hot rolled steel prices reached another eyebrow-raising milestone this week, hitting an average of $1,300 per ton ($65/cwt), which is an all-time record even adjusting for inflation from the previous high of $1,070 per ton recorded by Steel Market Update in 2008. Flat rolled prices rose by an additional $10-30 per ton as the market […]
By CRU Senior Analyst Helen O’Cleary from CRU’s Zinc Monitor. Zinc use has been optimized on an ongoing basis for decades as technological advances lead to lower raw materials usage and the development of higher-performing alloys with a lower zinc content. This is particularly true of the galvanizing industry, which accounts for around 60% of […]
This report examines the import share of sheet, plate, long and tubular products. As of January, imports’ share of total sheet products was 12.8%, up marginally from 12.3% in December. Although minimal, imports of sheet products have posted increases for two consecutive months after declining for seven consecutive months following the most recent peak of 16.6% […]
Steel prices simply continue to move higher—as do the anxiety levels of many service center and manufacturing executives. Hot rolled steel set yet another record this week, according to Steel Market Update’s check of the market, reaching an average of $1,270 per ton, topping the previous high mark set in 2008 by $200 per ton. […]
Steel prices simply continue to move higher—as do the anxiety levels of many service center and manufacturing executives. Hot rolled steel set yet another record this week, according to Steel Market Update’s check of the market, reaching an average of $1,270 per ton, topping the previous high mark set in 2008 by $200 per ton. […]
Steel prices took another bite out of the record books in March. The advent of March shows flat rolled and plate steel prices are still roaring upwards, with hot rolled hitting another record high of $1,240 per net ton, according to Steel Market Update’s check of the market this week. Prices generally moved up in […]
John Packard founded Steel Market Update in 2008 after spending 31 years actively selling steel in the service center, steel mill and trading company segments of the industry. He is currently President & CEO of Steel Market Update which was sold to CRU in 2018. Steel Market Update is a leader in collection of market […]
U.S. crude steel production fell sharply in January 2021 versus the same month last year even as production rose in most other major steelmaking nations, according to figures from the World Steel Association. And with domestic supplies scarce, some buyer sources have told Steel Market Update that they are taking a closer look at the […]
Among steelmaking raw materials, the prices of iron ore, pig iron and steel scrap moderated through February following large gains seen in previous months. Prices declined as much as 16% month-over-month for those three products, but remain 34-57% higher compared to three months prior and as much as 87% higher than levels one year ago. […]
Many buyers have been expecting lead times for deliveries of spot steel orders to begin shortening in response to added mill capacity and more import arrivals, but there’s no hint of such a change yet in Steel Market Update lead times data. In fact, SMU’s check of the market this week shows lead times for […]
Many buyers have been expecting lead times for deliveries of spot steel orders to begin shortening in response to added mill capacity and more import arrivals, but there’s no hint of such a change yet in Steel Market Update lead times data. In fact, SMU’s check of the market this week shows lead times for […]
Lead times for spot orders of cold rolled and coated products have now extended to more than 10 weeks, while lead times for hot rolled now exceed nine weeks, based on Steel Market Update’s check of the market this week. Despite widespread expectations that mill lead times are overdue to reverse course as supplies catch […]
AM/NS Calvert has quietly increased prices for new spot orders by $40 per ton ($2/cwt), according to market participants. The move–which was effective on Feb. 16 but not widely announced–will see base prices for hot-rolled coil increase from $1,160 per ton to $1,200 per ton, sources said. Base prices for cold-rolled and coated products will […]
Speculation that hot rolled steel prices could reach $1,200 per ton drew scoffs from some quarters just two months ago, yet here we are. Steel Market Update’s check of the market this week shows the average HR price up a further $20 per ton to yet another record high. The HR price surpassed the former […]
This report examines the import share of sheet, plate, long and tubular products. As of December 2020, imports’ share of total sheet products was 12.3%, up from 11.4% in November. The increase, albeit marginal, is notable as it’s the first increase for imports after declining for seven consecutive months following the most recent peak of 16.6% in […]
Some of you may have noticed that we have adjusted our language when it comes to the SMU Price Momentum Indicator. At this moment, the momentum indicators for hot rolled, cold rolled, galvanized, Galvalume and plate steels are pointing toward higher prices over the near term (next 30 to possibly as far out as 60 […]
Despite all the speculation about an impending peak, Steel Market Update’s check of the market this week shows steel prices continuing to rise. SMU puts the current average HR price at a new high of $1,180 per ton, the fifth new high-water mark since the second week of January when the spot market surpassed the […]
Among steelmaking raw materials, the prices of iron ore, pig iron and scrap saw large gains in January compared to months prior, up as much as 86 percent year over year. Coking coal prices, which rebounded compared to recent months, were still down 9 percent in January versus prices one year ago. Zinc prices have declined […]
U.S. flat-rolled steel prices remain on the rise thanks to strong demand, thin spot supplies and limited short-term competition from imports. While some sources think imports could send domestic prices lower, others note that foreign steel suffers from the late deliveries that have plagued customers of domestic mills. “Too much risk ordering foreign steel with lead times into […]
Steel prices continue to trek upward. But the pace has slowed, and questions about whether the market is at or near a summit have re-emerged. “Talked to two large OEMs that are postponing buys for the next few weeks. They believe we are at peak right now,” one respondent to Steel Market Update’s check of […]
As prices soar to historical high levels, we are constantly probing, looking for signs of a crack in flat rolled or plate steel prices. Nucor announced higher plate base prices today with discrete plate being referenced at $51.00/cwt ($1,020 per ton). Here are some of the “interesting” comments we received from steel buyers this week: […]
The average lead time on spot orders of hot rolled steel from the mill declined slightly for the second time in Steel Market Update’s biweekly survey and is now more than a half-week shorter than at this time last month. Lead times for other flat rolled products remained relatively unchanged, however, in SMU’s latest check […]
After registering a slight dip in Steel Market Update data two weeks ago, lead times for delivery of spot orders of hot rolled steel inched back out again this week to an average of nearly eight weeks. SMU and most in the market have been watching closely for signs that lead times are beginning to […]
Earlier this week I received a note from one of our readers regarding the plate price index and the changes we recently made to the index (FOB Mill vs. Delivered pricing). We were asked how we are accomplishing this, and how do our members reconcile the historical data that was based on delivered pricing versus […]
Earlier this week I received a note from one of our readers regarding the plate price index and the changes we recently made to the index (FOB Mill vs. Delivered pricing). We were asked how we are accomplishing this, and how do our members reconcile the historical data that was based on delivered pricing versus […]
Steel prices seem to be changing by the minute, and so far always in an upward direction. What’s the going price for hot rolled? “Who knows? Ask me again after lunch,” quipped one respondent to Steel Market Update’s check of the market this week. SMU estimates the current average price for HRC is at a […]