Sheet price hikes announced last week by domestic mills appeared to have succeeded in putting a floor under tags this week. The question now is to what extent the increases will stick and whether those gains will be sustainable. Our hot-rolled coil price reflects broader market trends. SMU’s average HRC price stood at $615 per […]
The bottom end of SMU’s sheet price ranges firmed up this week following price hikes of $60 per ton ($3 per cwt) announced by Cleveland-Cliffs and US Steel on Monday. It’s not clear yet whether the price increases will stick in full, in part, or simply stop the bleeding. Case in point: Our sheet price […]
SMU’s sheet prices slipped again this week. But some market participants predicted that sheet was at or near a bottom. The anticipation of that bottom appeared to pull some big buyers off the sidelines. Large purchases from some pulled the low end of our hot-rolled coil range below $600 per ton ($30 per cwt) and […]
Steel sheet prices fell across the board again this week, with hot-rolled coil prices dropping to their lowest point since late September 2020 – more than two years ago. But industry opinion about the direction of prices has diverged. That’s a significant shift from prior weeks, when sentiment was almost uniformly bearish. Some market participants […]
Imported sheet and plate products arrived at US ports at a slower clip in September, accounting for a lower share of the domestic market for the third straight month. That’s according to a Steel Market Update analysis of import data from the US Commerce Department and domestic shipment figures from the American Iron and Steel […]
Sheet prices fell across the board again this week as the slow grind lower that we’ve seen since last spring continued to gain speed. Hot-rolled coil prices fell $30 per ton ($1.50 per cwt) week-over-week. Declines in coated products were more pronounced, with cold rolled down $55 per ton, galvanized down $35 per ton, and […]
Sheet and plate prices fell across the board once again this week as market participants continue to question when and where the market might bottom. Some not long ago predicted that hot-rolled coil prices wouldn’t fall below $800 per ton ($40 per cwt). Our average price is now well below $700 per ton, with some […]
Galvanized prices continue to drop, as discussed during this month’s call of the Sheet Metal/Air Handling Council of the Heating, Air-conditioning & Refrigeration Distributors International (HARDI). Prices have been steadily dropping for the past six months despite stable demand. A few highlights from the call include the differential between hot-rollled and cold-rolled coil being in […]
Domestic sheet prices slipped again this week across all sheet and plate products. It’s the continuation of a mostly downward trend on the sheet side that we’ve seen since mid/late April. Hot-rolled, cold-rolled and coated products were all down $20–25 per ton ($1–1.25 per cwt). Plate prices slipped a more modest $10 per ton. SMU’s […]
The US International Trade Commission (ITC) narrowly voted to revoke anti-dumping and countervailing duties on Brazilian hot-rolled coil. The move comes after US trade officials decided to let duties on Brazilian cold-rolled coil expire – a change that has raised the ire of some domestic mills. The revocation is notable because it could allow for […]
US sheet prices continue to slide, and the weakness in the domestic market has buyers confident that they can get domestic suppliers to negotiate. For hot-rolled coil, imports have not been very advantageous relative to futures. There have been some workable offers for tandem mill products. But buyers have been more inclined to buy domestically or […]
Steel prices trended lower again this week, the second consecutive week of moderate declines, according to Steel Market Update sources. Sheet prices declined between $10–30 per net ton compared to last week, now at levels not seen since late 2020. Plate prices were broadly unchanged from last week, but are slowly easing towards levels last […]
Imported sheet and plate products arrived at US ports at a slower clip in August, resulting in them accounting for a lower share of the domestic market for the second straight month, according to a Steel Market Update analysis of import data from the US Commerce Department and domestic shipment figures from the American Iron […]
Domestic sheet prices fell sharply this week, marking their first substantial drop following nearly two months of mostly sideways or modestly downward moves. Another month of falling scrap prices appears to have been the catalyst. Another is this: Mills that had talked about discipline on the way up are now fighting for market share, sources […]
Sheet prices continued to tread water this week, with modest declines in hot-rolled coil and galvanized base prices offset in part by minor gains in cold-rolled coil and in Galvalume. Plate prices were also flat, following declines in prior weeks, on the heels of Nucor on Monday announcing unchanged pricing for discrete plate. Our benchmark […]
Prices for steel sheet remained mostly flat again this week, up or down modestly depending on the product. Hot-rolled coil was up $5 per ton ($0.25 per cwt), cold-rolled was down $10 per ton, and both galvanized and Galvalume base prices were down $5 per ton. What we’ve seen for the last month is an […]
Altos Hornos de México (AHMSA) has restarted its electric arc furnace (EAF) in Monclova, Coahuila, which had been down since July due to a failure at its electrical substation. Work to repair the substation was slowed by difficulties in sourcing the right equipment, which in turn delayed the restart of the EAF, according to a […]
Imported sheet and plate products arrived at US ports at a slower clip in July, resulting in them accounting for a lower share of the domestic market, according to US Commerce Department data. Imports’ share of US sheet and plate markets peaked in December, with sheet reaching its highest level in the past 4.5 years. The trend […]
Sheet prices drifted sideways to down this week, while plate prices fell substantually following the Nucor price decrease announcement on Monday. SMU’s hot-rolled index eased an average of $15 per net ton this week to $770 per ton. This is now tied with our late August price for the lowest HRC price seen since November […]
Sheet and plate prices continued to drift sideways this week as steel mills attempt to hold the line despite weak signals from the scrap market. Mills are more unified in trying to hold the line around $800 per ton ($40 per cwt) on hot-rolled coil following deep discounting ahead of announced price increases last month. […]
Sheet and plate prices were flat or down this week as some market participants questioned whether tags might be beginning to inflect lower. Hot-rolled and cold-rolled prices were down $5 per ton week over week. Galvanized (down $55 per ton) and Galvalume (down $40 per ton) fell more significantly. The steeper declines in coated products […]
Flat-rolled steel prices were steady to up based on the data points SMU collected this week. There’s undoubtedly been pressure from recent mill price hikes, but it’s still far too early to tell if they will stick or if this is just a blip. Sheet prices rose for each of our products this week. The […]
Sheet prices are down across the board this week, putting big cracks in any hopes that hot-rolled coil prices would find a bottom around $800 per net ton ($40 per cwt). The declines came as market participants reported that at least one large producer had cut deals at low levels and, in doing so, put […]
Sheet prices were mixed this week as market participants continued to debate whether a recent round of price hikes had stuck. While some said the increases would provide a floor and prevent further price erosion, others said prices were more likely to resume their downward trend in the weeks ahead. There were also questions about […]
Algoma Steel and United Steelworkers (USW) Local 2251 have once again narrowly averted a potential labor disruption. The Sault Ste. Marie, Ontario-based sheet and plate producer said Local 2251 had agreed to put the company’s “last offer” to union members for a vote. The union has scheduled ratification votes on the contract from Aug. 29-Aug. […]
Imported sheet and plate products arrived at US ports at a higher clip in June, resulting in them accounting for a larger share of the domestic market, according to US Commerce Department data. Imports’ share of US sheet and plate markets peaked in December, with sheet reaching its highest level in the past 4.5 years. The trend […]
A fire at one of Algoma Steel’s coal conveyors is not affecting iron and steelmaking operations at the company’s mill in Sault St. Marie, Ontario. But coke production will be reduced while the damage is repaired. The fire occurred on Aug. 7, 2022, on one of the conveyors that supplies coal to two of Algoma’s […]
Algoma’s plate mill is up and running following the first phase of a modernization project that was completed in June. The second phase of the expansion, initially expected to be finished by November 2022, has been moved to June 2023, a company spokeswoman told SMU on Tuesday, Aug. 9. The reason: “to support our customers […]
Algoma Steel Group posted solid profits in its fiscal first quarter on rising steel prices, despite higher raw material costs for iron ore, scrap, alloys and natural gas. The Sault Ste. Marie, Ontario-based flat-rolled steelmaker also said the gains came despite a “significant” planned outage at its plate mill for a first phase of upgrades. […]
New sheet and plate capacity from Nucor will be entering the market in force by the end of this year, just in time for an anticipated increase in infrastructure demand, company executives said. Whether those facilities ramp up to their nameplate capacity will ultimately depend on demand, they added. “While we recognize there is considerable […]