Steel Market Update’s poll of buyers on Monday and Tuesday showed further small declines for flat rolled steel prices, while plate prices were up a bit. No sign yet of a sharp correction as prices continue to ease downward. The benchmark price for hot rolled is now down to $1,830 per ton, $25 lower than […]
By CRU Senior Analyst Thais Terzian and Analyst Chris Bandmann, from CRU’s Crude Steel Market Outlet, Nov. 15 There is currently a lot of market discussion that the EU may act to restrict scrap exports. Here we look at who could be hurt and who might see opportunities. Other regions have already acted to protect […]
Flack Global Metals (FGM) is now a member of the CME Group, making it the first North American metals distributor to join the derivatives marketplace, the company said on Tuesday. The Cleveland-based service center said the move will allow its risk management team to provide even greater liquidity to buyers of flat-rolled products as well […]
Raw steel production by U.S. mills rebounded after falling for three straight weeks, and down five out of the last seven weeks. Domestic raw steel production was estimated at 1,856,000 net tons in the week ending Nov. 13, while the average mill utilization rate rose to 84.1%, according to the American Iron and Steel Institute […]
Hot-rolled coil prices continue to slide. And galvanized base prices are holding more or less steady. What gives? Check out the slide below. The green line is galvanized base prices. The blue line is lead times. Prices are on the left-hand side of the slide. Lead times are on the right. Prices have been around […]
Imports of less-expensive sheet and plate products have been on the rise for the past five months as buyers continue to seek relief from record-high steel prices in the U.S. September Commerce Department data show imports’ share of the U.S. flat-products markets at their highest levels in the past 4-5 years. Imports’ share of total […]
By Greg Wittbecker, Advisor, CRU Group Quotas in exchange for exemption, a bad precedent for other countries There has been much written about the new détente between the EU27 and the USA in the aftermath of the deal to suspend duties on European steel and aluminum. There are also reports that something may also be […]
September apparent steel supply increased by 90,000 tons over August to 9.92 million net tons, according to the latest U.S. Department of Commerce and American Iron and Steel Institute data. This is the highest supply level seen in more than six years, going back to January 2015 when supply surpassed 10 million tons. September supply is up […]
The following article on the hot rolled coil (HRC), scrap and financial futures markets was written by Jack Marshall of Crunch Risk LLC. Here is how Jack saw trading over the past week: Hot Rolled Spot HR has declined each of the last three Wednesday’s for a total loss of $86/ST. Spot HR has lost […]
Steel Market Update is pleased to share this Premium content with Executive members. For information on upgrading to a Premium-level subscription, email Info@SteelMarketUpdate.com. U.S. raw steel production in September eased 4.9% from August to 7.89 million net tons, a 408,000-ton seasonal decline, according to American Iron and Steel Institute data. One month prior, production had reached a 20-month high […]
By CRU Principal Analyst Josh Spoores, from CRU’s Steel Sheet Products Monitor, Nov. 10 Global sheet prices have continued to fall, though declines have not been consistent across all regions. Overall, CRU’s Global Flat Products Steel Price Indicator (CRUspi flats) fell for the second consecutive month, declining by 2.9% and is now at its lowest […]
U.S. steel exports decreased 4% from August to September to 732,000 tons, according to the latest U.S. Department of Commerce data. September marks the lowest monthly export level seen in six months. Recall that in March and June of this year, we saw the two highest monthly export levels in the last three years (790,000 and 778,000 […]
Even as domestic prices ease, foreign steel imports continue to tempt U.S. buyers with potential discounts of 24-43%, according to Steel Market Update’s latest comparison of domestic and foreign hot rolled steel prices. Foreign hot rolled steel prices are now theoretically $452-801 per ton cheaper than domestic steel, after taking freight costs, trader margins and tariffs […]
Steel Market Update’s check of the market this week shows both flat rolled and plate prices declining by another $10-25 per ton. The declines were not unexpected and are in line with the downtrend that has materialized in the last two months as seasonal dips in demand and competition from imports put pressure on domestic […]
Ferrous scrap prices saw an unexpectedly big jump in November, with shredded scrap selling as high as $75/GT above October levels. Prime scrap rose $20/GT, sources tell Steel Market Update. Observers were expecting higher prices in November on strong export demand and some seasonal tightening of supplies, but were surprised by the size of the […]
On Monday, Nov. 8, NLMK notified customers of an upward revision to their galvanized steel coating extras, effective on orders starting January 2022. Zinc prices soared in October, reaching a record high of $1.74 per pound on Oct. 15. Prices have since declined, down to $1.48 per pound as of Nov. 9. Recall that the last round of […]
By CRU Principal Analyst Erik Hedborg, from CRU’s Steelmaking Raw Materials Monitor, Nov. 9 Iron ore prices remain under pressure as Chinese steel production levels remain low and iron ore inventories continue to pile up, both at ports and at steel mills. A price of $92 /dmt is the lowest seen since May 2020, and […]
Raw steel production by U.S. mills slipped for the third straight week, now down five out of the last six weeks. Domestic raw steel production was estimated at 1,841,000 net tons in the week ending Nov. 6, while the average mill utilization rate dipped to 83.4%, its lowest reading since the week of July 10, […]
By Greg Wittbecker, Advisor, CRU Group Since I spoke at the Fall Management Meeting, the market has continued to experience tremendous volatility and new variables to consider. CRU has recently updated its expectation for market balances, premiums and LME prices. These forecasts can be seen in detail through our Aluminum Market Outlook subscription. Here are […]
SMU contributor Tim Stevenson is a partner at Metal Edge Partners, a firm engaged in Risk Management and Strategic Advisory. In this role, he and his firm design and execute risk management strategies for clients along with providing process and analytical support. In Tim’s previous role, he was a Director at Cargill Risk Management, and […]
Final Census data shows that September foreign steel imports increased 17% from August to 3.26 million net tons and a 28-month high. October import licenses are currently at 2.47 million tons as of Nov. 4, down 24% from September and down 11% compared to August. The last time total monthly import levels were this high was April […]
By CRU Principal Analyst Josh Spoores Trade representatives from the USA and Europe came to an agreement at the end of October in regard to the Section 232 tariffs on steel and aluminum. The Department of Commerce further announced on Oct. 31 that consultations regarding the trade of steel remain ongoing between the USA and […]
The Steel Tube Institute has named Dale Crawford as its next executive director. He replaces Joseph Anderson, who is retiring. Crawford has served as director of STI’s Conduit Division since May 2017 and will continue in the Conduit Committee leadership role in addition to his responsibilities as executive director. Anderson, who has carried dual roles […]
As expected, steel prices are volatile and unpredictable as the market approaches year-end. Hot rolled continued its slow, gradual descent averaging $1,875 per ton this week, down another $10, based on Steel Market Update’s survey data gathered on Monday and Tuesday. Cold rolled and coated products, on the other hand, saw small increases to around […]
By CRU Senior Analyst Ryan McKinley from CRU’s Steel Sheet Products Monitor Falling demand in most markets around the world has continued to weigh on steel sheet prices. Meanwhile, the announcement that the USA will remove Section 232 tariffs on steel and aluminum producers in the EU and replace them with a quota system means […]
Raw steel production by U.S. mills slipped for the second consecutive week following their highest tonnage output since the pandemic started just two weeks prior. Domestic raw steel production was estimated at 1,860,000 net tons in the week ending Oct. 30, while the average mill utilization rate was 84.3%, according to the American Iron and […]
Editor’s note: SMU Contributor David Feldstein is president of Rock Trading Advisors. Rock provides customers attached to the steel industry with commodity price risk management services and market intelligence. RTA is registered with the National Futures Association as a Commodity Trade Advisor. David has over 20 years of professional trading experience and has been active […]
Even as domestic hot rolled steel prices fall below $1,900 per ton, cheaper foreign steel imports continue to tempt U.S. buyers with potential discounts of 25-43%, according to Steel Market Update’s latest foreign versus domestic hot rolled steel price comparison. Foreign hot rolled steel prices are now theoretically $478-803 per ton cheaper than domestic steel, […]
Domestic mills plan to announce higher zinc coating extras as soon as this week, according to market participants. The higher coating extras would be effective Jan. 1, 2022, they said. At least two domestic mills have also confirmed that extras will move higher. Zinc is used to make galvanized products. It prevents rust. Zinc prices […]
Steel imports into the United States jumped by nearly 35% in the first nine months of this year, versus the same period in 2020, according to Census Bureau data from the American Iron and Steel Institute (AISI). Tight supplies and record-high domestic steel prices have attracted a host of imports, which are reportedly some $400-800 […]