Steel Products

U.S. Flat Rolled & Plate Inventories Dropped in June
Written by John Packard
July 21, 2019
Steel Market Update has been analyzing service center inventories for two years now. With our acquisition by the CRU Group, we expanded the breadth and depth of our coverage. Our new Service Center Inventories Index will be rolled out to the public at the 2019 SMU Steel Summit Conference in Atlanta at the end of August. Our intention is to share the basic product with our Premium level subscribers beginning in September 2019.
Overview
The latest Steel Market Update Inventory Survey shows U.S. service centers continue to pare down their inventories. In June, the number of shipping days of supply for sheet fell to the lowest level seen since February, and for plate, it was the lowest level seen all year.
Flat Roll inventories at 50.9 days
At the end of June, U.S. service centers reported a 1 percent drop in inventories with less than a 2 percent decrease in shipments month on month. The result was an apparent flat month-on-month calculation of 2.55 months of supply in June.
However, months of supply on hand does not tell the full story because June had 20 shipping days, compared to May’s and April’s respective 22. If you just look at the months of supply, it appears that months of supply has held flat around 2.5 for the last three months (2.54 in April; 2.53 in May; and 2.55 in June). When you consider the number of days, you see that shipping days of supply fell to 50.9 in June from May’s 55.6 and April’s 55.9.
Similarly, the shipping days of supply on order clearly shows an uptick in purchasing. Service centers had 33.4 days of supply on order at the end of June, up from 30.5 in May. The percentage of inventory on order jumped to 66 percent in June from 55 percent.
The amount of sheet inventory committed to contracts also increased to 58 percent from 47 percent, which is indicative of either service center customers or the service centers themselves looking to lock in lower prices when prices were bottoming.
Looking ahead, we expect that the amount of flat rolled steel on order will remain elevated, given the high-volume orders placed in late June and early July, as prices were finding a bottom. This will reduce the amount of material that will be purchased at higher prices. We expect inventories to remain elevated in July and outbound shipments to decrease because of seasonal factors; however, this could be offset by additional shipments at lower prices earlier in the month. (ARTICLE CONTINUES BELOW)
{loadposition reserved_message}
Plate Inventories stand at 56.4 days
U.S. service center inventories for plate in June shrank by 8 percent while shipments decreased 9 percent month on month.
Shipping days of supply dropped to 56.4 days from 61.4 in May; 56.4 is the lowest level recorded this year.
Service centers carried 2.82 months of supply for plate in June, up from 2.79 in May.
The amount of inventory on order has been relatively steady at 40 percent in June and 39 percent in May. This translates to 22.6 shipping days of supply, a new low for the year and down from 23.8 in May.
The amount of plate inventory committed to contracts was flat at 40 percent in June.
As plate prices have been tumbling, buyers have shunned new orders. The lessening supply on order – at 22.6 days in June – will translate to lighter inventories, which could support possible price increases.

John Packard
Read more from John PackardLatest in Steel Products

US rig count up, Canada declines
Oil and gas drilling activity was mixed this week, according to Baker Hughes. US rig counts expanded for a second straight week, while Canadian activity continued its seasonal slowdown of eight consecutive weeks.

US, offshore CRC prices continue to diverge
US cold-rolled (CR) coil prices declined again this week, slipping for a third straight week. Most offshore markets did the opposite, moving higher this week.

S232 lifts EU HR price over US, Asian HR still well behind
Domestic hot-rolled coil prices were flat this week after dropping for four straight weeks. Most offshore markets bucked the trend and gained ground.

SMU Steel Demand Index dips into contraction
SMU’s Steel Demand Index has moved into contraction, according to late April indicators. The slowdown comes in response to growing tariff uncertainty after the index reached a four-year high in late February.

Nucor selects Fives Group for new galv line at CSI
Nucor Corp. has tapped Fives Group as its partner in designing and manufacturing the new continuous galvanizing line being added at its California Steel Industries (CSI) joint venture in Fontana, Calif.